For a full list of M12 pinouts see Connector Pinout List
NACS
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) | Pin 5 (Grey) |
| 12V SPO | SDI-12 | 4-20mA | GND | Counter |
NAAC
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) | Pin 5 (Grey) |
| 12V SPO | 4-20mA #2 | 4-20mA #1 | GND | Counter |
NAAS
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) | Pin 5 (Grey) |
| 12V SPO | SDI-12 | 4-20mA #1 | GND | 4-20mA #2 |
NASV
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) | Pin 5 (Grey) |
| 12V SPO | SDI-12 | 4-20mA | GND | 0-5V |
For a full list of M12 pinouts see Connector Pinout List
MAC
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| 12V SPO | Counter | 4-20mA | GND |
MAS
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| 12V SPO | SDI-12 | 4-20mA | GND |
MCCD
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| Tamper | Counter #1 | Counter #2 | GND |
ENV
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| 12V SPO | Counter | 4-20mA | GND |
MSDIM12
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| 12V SPO | SDI-12 | 4-20mA | GND |
FSDIM12/FSM12
| Pin 1 (Brown) | Pin 2 (White) | Pin 3 (Blue) | Pin 4 (Black) |
| 12V SPO | SDI-12 | Counter | GND |
| Pin 1 (Brown) | Pin 3 (Blue) | Pin 4 (Black) |
| Input Power 12V+ | N/A | GND |
Important! Although an external antenna may fit, it is important to identify and use the correct antenna that supports the required cellular band. Attaching an antenna that does not support the required cellular band can severely degrade the performance of a device or stop the device connecting all together.
See the Antennas page for more information regarding antennas
Australia
4G Antennas
Compatible whip antennas have an orange tip. Compatible stubby antennas have a shiny black surface and typically a gold finished connection. Compatible puck antennas support the 700Mhz band.
3G Antennas
Compatible whip antennas have an yellow tip. Compatible stubby antennas have a matt black surface and typically a silver finished connection. Compatible puck antennas support the 850Mhz band.
|
|
New Zealand
4G Antennas
Forthcoming
3G Antennas
Forthcoming
3G LED Sequence - WASP2/COBRA2
Activation LED Sequence
| LED | Solid or Blinking | State |
| Blue | Solid | Swipe Detected and logger is NOT in transport mode |
| Blue | Blinking | Swipe Detected and logger is in transport mode |
| Blue and Red | Alternate every 200ms | Battery Protection mode detected (Only for Cobra products) |
| Blue and Green | Alternate every 200ms | Battery Protection mode detected (Only for Cobra products) - unit is charging |
| Blue | Blinking | Modem ON and registered |
| Green | Blinking | Modem successfully connects and uploads data |
| Red | Solid | Modem fails to connect |
Signal Strength - Blue LED
| Flashes | Signal Strength |
| 1 | < 20% |
| 2 | < 40% |
| 3 | < 66% |
| 4 | < 86% |
| 5 | > 86% |
Red LED Codes
| Flashes | Meaning |
| 1 | No SIM card present. |
| 2 | Failed Network Registration. |
| 3 | Fail Network Connection (Got a registration, but could not get a GPRS connection). |
| 4 | Connection Timed Out, was taking too long. |
| 5 | Fail Web Connection (Got a GPRS session, can't create a TCP connection to the server). |
| 6 | Failed Response from OutpostCentral.com (send data but did not receive the OUTPOSTOK string). |
| 7 | This error indicates that the device has failed to connect to the network 5 or more times. |
| 8 | Radio Timeout. |
| 9 | Radio failed. |
UBA LED Sequence - WILD-M-B/WILD-M-R
Activation LED Sequence
| LED | Solid or Blinking | State |
| Purple | Solid | Unit booting up |
| Blue | Blinking | Swipe Detected and logger is in transport mode |
| Red | Solid | Modem failed to connect to the server |
| Blue and Red | Alternate every 200ms | Battery Protection mode detected (Only for R products) |
| Blue and Green | Alternate every 200ms | Battery Protection mode detected (Only for R products) - unit is charging |
| Blue | Blinking | Modem ON and registered |
| Green | Blinking | Modem successfully connects and uploads data |
| Red | Solid | Modem fails to connect |
Signal strength - Blue and Green LEDs
| Flashes | Signal Strength |
| 1 | < 20% |
| 2 | < 40% |
| 3 | < 66% |
| 4 | < 86% |
| 5 | > 86% |